horse, horses and more horses more horses
horses for sale horse news

Printer-Friendly Version

Email This Story

Post Your Opinion

TOP CLASSIFIED ADS

Featured Item:

   MISC $89

Featured Colt:

   Quarter Horse

Featured Item:

   MISC $56

Featured Item:

   SADDLE $1,649

Featured Item:

   REAL ESTATE $1,150,000

SPECIAL DEALS

Posted: Monday, August 19, 2002

Why not a 2-ton?

By Kent Sundling

I have worn out my share of trucks. No I really mean I wore them out! When I was done with them they were worth about $20 a ton for scrap metal. The springs were arced the wrong way, the box was gone, and you couldn't tell what color the engine was from the oil dripping off it. But by then I could replace the starter, alternator, u-joints or clutch with my eyes closed.

Being a rancher/farmer meant my truck had to pay for itself with use. Being overloaded most of the time is what got the job done. I hauled livestock, hay, wool, tractors, balers, backhoes, buildings, trees and whatever "kind of fit" the trailer. I was overweight, over width, and under trucked. No not me, the truck!

After I replaced another set of u-joints in the drive shaft, I thought maybe I'm working my 1-ton dually too much. It had 300,000 miles on it and my Korean replacement door from the last time I jackknifed the trailer was leaking so much air I couldn't hear the weather report on the AM radio. So time for my next workhorse. I saw an ad for some furniture van body 2-ton trucks. They had 90,000 miles on them so they were already broke-in. My neighbor and I each bought one. Mine was a C65 Chevy. I took the 18 ft. van body off, leaving a flatbed and added a recessed gooseneck ball to the rear of the rear axle. I pulled a 32 ft. flatbed triple axle trailer with it and had 12 feet to haul cargo behind the cab in front of the gooseneck. That was the most reliable truck I ever pulled with. It had a 366 cu engine and a 5-speed manual transmission with a 2-speed Eaton axle. I loved that truck and couldn't hurt it. Ten gears, I was in heaven! It even rode nice. I couldn't tell it was loaded, it had low axle ratios and would pull anything 70 MPH. Tires cost more but they also lasted longer. The most expensive repair I did to the truck was replace the king pins in the front axle. The next 100,000 miles were all trailer miles. So I do like bigger trucks with bigger brakes, trannies, axles and springs.

If you also decide you pull too much for a 1-ton, now the next decision is between new and used. One of the nice things about a used big truck, (two-ton or 26,000 GVWR) is they can last like an "Eveready Battery Bunny." If you go out to farm country, you can find the old "Over The Road" rigs that are 30 years old plus still hauling corn or hay. Some trailer dealers also sell big trucks even conversions that are classified as an RV. The rental businesses like U-haul or Penske sell thousands of used 2-ton trucks a year. Penske is friendly with GM so a lot of these used van trucks can be found at new GMC franchises. Several of the 2-ton used trucks that U-haul and Penske would have will have the a low profile kit with just 16 in. tires, so they won't be any harder to climb up into than a 1-ton. Some of them will even have Allison automatics, probably AT545 and a few diesels. I think my truck came from Mayflower originally. It had a hydraulic lift, which I used a couple of years and then took off. So check out a few of the big moving companies also.

Most of the 2-ton trucks will have 6 to 10 gears in the manual transmission or 4 or 5 speeds with an automatic transmission. These trucks are made to be loaded all the time. My 2-ton gave me the least amount of trouble hauling loads and pulling trailers. It's also nice to have a heavy truck pulling the trailer. It gives you more control when you brake going down hill keeps the trailer behind you instead of trying to pass you.

If you choose a new big truck, choices range from GM 6500, 7500 and Ford F650, F750 to Freightliner FL60, FL70, International 4700, Peterbuilt T-330 and Kenworth T-300. And with the big boys you can get engine or exhaust brakes, crew cabs, any diesel engine you want, more gears, air ride and air seat. Yes air seat! Now the biggest down side is the cost. So it's a bigger decision. You can finance or lease for a longer term. And they have a better resale value. You are also looking at a truck designed for one million miles instead of a target of 300,000 miles for a good pickup truck diesel.

Another consideration is drivers license. I had a Class A drivers license in Colorado, which would let me drive anything in the old days, and I could have grand fathered in with the CDL license but I wasn't smart enough back then to see the need.

This is a gray area for the whole country. Pickup trucks pulling trailers and big trucks pulling gooseneck trailers seems to confuse the DOT, (Department of Transportation.) I know some people who get tickets because they are over 26,000 GVWR (Gross Vehicle Weight Rating) and don't have a CDL and log books and I know people who have never been pulled over with rigs that look totally commercial. Even with national CDL's you would think there is some kind of constant rule but each state DOT seems to not know what to do. 10 years ago in Colorado when I pulled everyday, I never stopped in a port with a loaded trailer even when I hauled large round bales 12' wide. But when I went threw Nebraska even with a stock trailer, I had to stop at the ports. Now the portable ports in Colorado would stop everybody. With the newest trend in the 2- ton trucks that are 26,000 GVWR but you add a trailer and you could be over the legal GVWR again. The one thing the DOT does agree on is RV's. Pull a fifth-wheel RV or a horse trailer with Living Quarters and I haven't seen where they require a CDL or logbook.

Another problem with a big truck and a short wheelbase and a single rear axle is the bounce. Some people ad weight to the rear frame so when not pulling a trailer is will bounce less. A nice heavy flat bed will help. If you always are hooked to a trailer it won't be a problem. My truck had a 18' flatbed, so I did use it without the trailer to haul things. It worked well for me but not everyone wants that long of a rig with a trailer.

Now as with any trailer pulling truck, you need to know the GCWR (Gross Combined Weight Rating,) with combines the truck and trailer. Also you need the tongue weight, as well as the axle ratings. All this combined to give you the big picture for your big truck option. Come visit my website and check out my "MrTruck's Insider Club," at www.MrTruck.com. Good Big Truck'n. Kent Sundling (MrTruck)

FEATURED SPONSORS